Поиск
Искать только в заголовках
От:
Искать только в заголовках
От:
Форумы
Новые сообщения
Поиск сообщений
Новости и анонсы
Новые статьи
Новые комментарии
Искать статьи
Что нового?
Новые сообщения
Новые медиа
Новые статьи
Новые комментарии к медиа
Комментарии к новой статье
Новые сообщения профилей
Последняя активность
Медиа
Новые медиа
Новые комментарии
Поиск медиа
Пользователи
Текущие посетители
Новые сообщения профилей
Поиск сообщений профилей
Вход
Регистрация
Поиск
Искать только в заголовках
От:
Искать только в заголовках
От:
Новые сообщения
Поиск сообщений
Меню
Приложение
Установить
Ответить в теме
Форумы
ВСЁ О МОТОЦИКЛАХ
Мотоциклы BMW
ROADSTER
Клуб в клубе :))) Обладатели и владельцы R1200C , R1200CL...
JavaScript отключён. Чтобы полноценно использовать наш сайт, включите JavaScript в своём браузере.
Вы используете устаревший браузер. Этот и другие сайты могут отображаться в нём некорректно.
Вам необходимо обновить браузер или попробовать использовать
другой
.
Сообщение
<blockquote data-quote="korova" data-source="post: 406967" data-attributes="member: 7120"><p>Выдержка из мануала:</p><p></p><p>BRAKE FLASH FEATURE:</p><p>(Brake Input wire must be hooked-up)</p><p>As long as the turn signals are active, applying the brakes will cause turn</p><p>signal bulbs to flash as brakes. The flash pattern begins with fast flash rate,</p><p>which slows down to solid ON after 2 ½ seconds.</p><p>NOTE! BOTH front and rear turn signal bulbs will flash during this short</p><p>interval – just as they flash together for turn signals. They are wired</p><p>together on the bike.</p><p>PROGRAMMING BRAKE FLASH FEATURE:</p><p>?????? Apply & Hold brakes first, then turn ignition on.</p><p>?????? Immediately begin pumping the brakes at least 6 to 8 times</p><p>?????? This is a toggle function – it activates it on or off upon each execution</p><p>BMW models with ABS brakes do not allow successive brake</p><p>applications to generate 12V distinctly, which is necessary for the</p><p>programming sequence.</p><p>You can use the Brake Input wire as a direct input to any 12V source</p><p>and perform the programming procedure described above.</p></blockquote><p></p>
[QUOTE="korova, post: 406967, member: 7120"] Выдержка из мануала: BRAKE FLASH FEATURE: (Brake Input wire must be hooked-up) As long as the turn signals are active, applying the brakes will cause turn signal bulbs to flash as brakes. The flash pattern begins with fast flash rate, which slows down to solid ON after 2 ½ seconds. NOTE! BOTH front and rear turn signal bulbs will flash during this short interval – just as they flash together for turn signals. They are wired together on the bike. PROGRAMMING BRAKE FLASH FEATURE: ?????? Apply & Hold brakes first, then turn ignition on. ?????? Immediately begin pumping the brakes at least 6 to 8 times ?????? This is a toggle function – it activates it on or off upon each execution BMW models with ABS brakes do not allow successive brake applications to generate 12V distinctly, which is necessary for the programming sequence. You can use the Brake Input wire as a direct input to any 12V source and perform the programming procedure described above. [/QUOTE]
Проверка
Ответить
Сверху
Снизу