Поиск
Искать только в заголовках
От:
Искать только в заголовках
От:
Форумы
Новые сообщения
Поиск сообщений
Новости и анонсы
Новые статьи
Новые комментарии
Искать статьи
Что нового?
Новые сообщения
Новые медиа
Новые статьи
Новые комментарии к медиа
Комментарии к новой статье
Новые сообщения профилей
Последняя активность
Медиа
Новые медиа
Новые комментарии
Поиск медиа
Пользователи
Текущие посетители
Новые сообщения профилей
Поиск сообщений профилей
Вход
Регистрация
Поиск
Искать только в заголовках
От:
Искать только в заголовках
От:
Новые сообщения
Поиск сообщений
Меню
Приложение
Установить
Ответить в теме
Форумы
ТЕХНИЧЕСКИЙ РАЗДЕЛ
Обмен опытом
ремонт R-серии
Датчики давления в колёса с Ебэя как альтернатива оригиналу
JavaScript отключён. Чтобы полноценно использовать наш сайт, включите JavaScript в своём браузере.
Вы используете устаревший браузер. Этот и другие сайты могут отображаться в нём некорректно.
Вам необходимо обновить браузер или попробовать использовать
другой
.
Сообщение
<blockquote data-quote="WIND" data-source="post: 467942" data-attributes="member: 3636"><p>самое интересное, что когда пошел по этому пути:</p><p>Option 3: waking a sensor manually (does not always work!)</p><p></p><p>As the sensors are still active for a while before going to sleep, your first thought would be to take the bike for a short ride, thus waking the sensors and allowing you to learn a sensor.. This however is NOT THE RIGHT WAY!! This will wake both sensors and when you instruct your RDC unit to learn a specific position, e.g. front wheel, Set A, the control unit will be receiving signals from both active TPM sensors and might not learn the right one, or any for that matter...</p><p></p><p>THE CORRECT ALTERNATIVE, also known as the "ALERT method" is to let the air out of the wheel rapidly (we simply depress the valve for around 10 seconds)... this rapid fall in pressure wakes the sensor and places it in an Alert mode, where it starts sending its data (which obviously includes its Sensor ID!).</p><p></p><p>Thus, to summarize, if you do not have a RDC wake-up tool, either enter the new Sensor ID manually in the Advance section (this of course assumes you noted the Sensor ID before refitting the wheel ;-) ), or when the GS-911 application asks you to use the wake-up tool, simply depress the valve of the tire that you want to wake for around 10 seconds, which will in turn wake the sensor in an Alert mode where it then sends its Sensor ID and pressure information....</p><p></p><p>на приборной панели мотоцикла давление отображалось и мигало.</p><p>однако, датчики, с уникальными ID в компьютер не прописались.</p></blockquote><p></p>
[QUOTE="WIND, post: 467942, member: 3636"] самое интересное, что когда пошел по этому пути: Option 3: waking a sensor manually (does not always work!) As the sensors are still active for a while before going to sleep, your first thought would be to take the bike for a short ride, thus waking the sensors and allowing you to learn a sensor.. This however is NOT THE RIGHT WAY!! This will wake both sensors and when you instruct your RDC unit to learn a specific position, e.g. front wheel, Set A, the control unit will be receiving signals from both active TPM sensors and might not learn the right one, or any for that matter... THE CORRECT ALTERNATIVE, also known as the "ALERT method" is to let the air out of the wheel rapidly (we simply depress the valve for around 10 seconds)... this rapid fall in pressure wakes the sensor and places it in an Alert mode, where it starts sending its data (which obviously includes its Sensor ID!). Thus, to summarize, if you do not have a RDC wake-up tool, either enter the new Sensor ID manually in the Advance section (this of course assumes you noted the Sensor ID before refitting the wheel ;-) ), or when the GS-911 application asks you to use the wake-up tool, simply depress the valve of the tire that you want to wake for around 10 seconds, which will in turn wake the sensor in an Alert mode where it then sends its Sensor ID and pressure information.... на приборной панели мотоцикла давление отображалось и мигало. однако, датчики, с уникальными ID в компьютер не прописались. [/QUOTE]
Проверка
Ответить
Сверху
Снизу